Adhesives
Showing all 14 results
-
Bostik Born2Bond GA-10 Gasketing Adhesive – 50 ml Accordion
$22.13 – $265.52Bostik Born2BondTM Gasketing anaerobic adhesives are a single component, cost effective alternative to conventional pre-formed gaskets on metal flanges. Flexible, durable and resistant to wear and tear, they can be used during installation or for preventative maintenance. Achieving 100% surface-to-surface contact, the adhesives create a cohesive, durable connection that can withstand vibration, extreme temperatures and exposure to oils, solvents and water. They also offer better stress distribution and, unlike traditional gaskets, do not require any ‘bedding-in’. GA-10 is an anaerobic gasketing material with high viscosity and medium strength. It is designed to withstand temperatures up to 200°C. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. KEY FEATURES Medium strength High viscosity / Paste Instant low pressure seal Outstanding fatigue strength Vibration resistant Corrosion prevention Prevents sagging and micro-movement Higher power transmission Single component Suitable for active and passive metals DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding Cleaner and wait until fully evaporated. 2. The product is designed for close fitting flanged parts with gaps up to 0.25 mm. 3. Apply manually as a continuous bead or by screen-printing to one surface of the flanges. 4. If the cure speed is too slow, use Born2BondTM Anaerobic Activator. 5. Tighten flanges after application. 6. Cured product can be removed by using of Born2BondTM Gasket &Adhesive Remover and a soft scraper. 7. Finish the cleaning process with a Born2BondTM Pre-bonding Cleaner soaked soft cloth. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Engines and powertrains Pumps and compressors Storage of liquids and gas Gearboxes and transmissions STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide TDS -
Bostik Born2Bond GA-18 Gasketing Adhesive – 50 ml Bottle
$19.68 – $236.12Bostik Born2BondTM Gasketing anaerobic adhesives are a single-component, cost effective alternative to conventional preformed gaskets on metal flanges. Flexible, durable and resistant to wear and tear, they can be used during installation or for preventative maintenance. Achieving 100% surface-to-surface contact, the adhesives create a cohesive, durable connection that can withstand vibration, extreme temperatures and exposure to oils, solvents and water. They also offer better stress distribution and, unlike traditional gaskets, do not require any ‘bedding-in’. GA-18 is a general purpose anaerobic gasketing material with high viscosity and medium strength. It is recommended for use on rigid iron, steel and aluminum flanges. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. This product is acceptable for use as a sealant in and around food processing areas according to NSF S2 (Registration No.163873). KEY FEATURES Medium strength High viscosity / Paste Instant low pressure seal Outstanding fatigue strength Vibration resistant Corrosion prevention Prevents sagging and micro-movement Higher power transmission Single component Suitable for active and passive metals DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding Cleaner and wait until fully evaporated. 2. The product is designed for close fitting flanged parts with gaps up to 0.25 mm. 3. Apply manually as a continuous bead or by screen-printing to one surface of the flanges. 4. If the cure speed is too slow, use Born2BondTM Anaerobic Activator. 5. Tighten flanges after application. 6. Cured product can be removed by using of Born2BondTM Gasket &Adhesive Remover and a soft scraper. 7. Finish the cleaning process with a Born2BondTM Pre-bonding Cleaner soaked soft cloth. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Engines and powertrains Pumps and compressors Storage of liquids and gas Gearboxes and transmissions STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide TDS -
Bostik Born2Bond PA-42 Pipe Sealing Adhesive – 50 ml Accordion
$22.13 – $265.52Bostik Born2BondTM Pipe Sealing anaerobic adhesives are a reliable, adaptable solution, suitable for all types of threaded metal pipes and fittings, and both new installations and preventative maintenance. Filling and sealing all voids, these single component adhesives provide 100% surface-to-surface contact, achieving a cohesive, durable connection that will not fail even when subjected to vibration, extreme temperatures or chemical substances. A convenient, cost-effective alternative to conventional sealing alternatives like hemp or PTFE tapes, these adhesives eliminate the need for additional inventory. PA-42 is an anaerobic thread sealant material with medium viscosity and medium strength. Ideal for hydraulic valves and threaded couplings. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. KEY FEATURES Medium Strength Medium Viscosity & Thixotropic Instant low pressure seal Fluorescenic 100% connection – no loosening Vibration resistant Corrosion prevention Single component Suitable for active and passive metals DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding cleaner and wait until fully evaporated. 2. If the cure speed is too slow of on inactive metals, use Born2BondTM Anaerobic Activator. 3. Apply the product into the threads, leaving the first thread free. Fill all voids thoroughly. 4. Properly tighten fittings with suitable tools. It will seal instantly to moderate pressures. 5. Wait for full cure to get maximum pressure resistance. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Engines and powertrains Pumps and compressors Storage of liquids and gas Gearboxes and transmissions STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide TDS -
Bostik Born2Bond PA-67 Pipe Sealing Adhesive – 50 ml Accordion
$22.13 – $265.52Bostik Born2BondTM Pipe Sealing anaerobic adhesives are a reliable, adaptable solution, suitable for all types of threaded metal pipes and fittings, and both new installations and preventative maintenance. Filling and sealing all voids, these single component adhesives provide 100% surface-to-surface contact, achieving a cohesive, durable connection that will not fail even when subjected to vibration, extreme temperatures or chemical substances. A convenient, cost-effective alternative to conventional sealing alternatives like hemp or PTFE tapes, these adhesives eliminate the need for additional inventory. PA-67 is an anaerobic thread sealant material with medium viscosity and medium strength. Ideal for hydraulic valves and threaded couplings. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. KEY FEATURES Medium Strength Medium Viscosity & Thixotropic Instant low pressure seal Fluorescenic 100% connection – no loosening Vibration resistant Corrosion prevention Single component Suitable for active and passive metals DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding cleaner and wait until fully evaporated. 2. If the cure speed is too slow of on inactive metals, use Born2BondTM Anaerobic Activator. 3. Apply the product into the threads, leaving the first thread free. Fill all voids thoroughly. 4. Properly tighten fittings with suitable tools. It will seal instantly to moderate pressures. 5. Wait for full cure to get maximum pressure resistance. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Engines and powertrains Pumps and compressors Storage of liquids and gas Gearboxes and transmissions STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide -
Bostik Born2Bond PA-77 Pipe Sealing Adhesive – 50 ml Bottle
$22.13 – $265.52Bostik Born2BondTM Pipe Sealing anaerobic adhesives are a reliable, adaptable solution, suitable for all types of threaded metal pipes and fittings, and both new installations and preventative maintenance. Filling and sealing all voids, these single component adhesives provide 100% surface-to-surface contact, achieving a cohesive, durable connection that will not fail even when subjected to vibration, extreme temperatures or chemical substances. A convenient, cost-effective alternative to conventional sealing alternatives like hemp or PTFE tapes, these adhesives eliminate the need for additional inventory. PA-77 is an anaerobic thread sealant material with medium viscosity and medium strength. Ideal for hydraulic valves and threaded couplings. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. KEY FEATURES Medium Strength Medium Viscosity & Thixotropic Instant low pressure seal Fluorescenic 100% connection – no loosening Vibration resistant Corrosion prevention Single component Suitable for active and passive metals DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding cleaner and wait until fully evaporated. 2. If the cure speed is too slow of on inactive metals, use Born2BondTM Anaerobic Activator. 3. Apply the product into the threads, leaving the first thread free. Fill all voids thoroughly. 4. Properly tighten fittings with suitable tools. It will seal instantly to moderate pressures. 5. Wait for full cure to get maximum pressure resistance. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Engines and powertrains Pumps and compressors Storage of liquids and gas Gearboxes and transmissions STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide TDS -
Bostik Born2Bond RA-03 Retaining Adhesive – 50 ml Bottle
$26.55 – $318.59Bostik Born2BondTM Retaining anaerobic adhesives are a cost effective, adaptable alternative or addition to mechanical retaining processes. Capable of bonding all types of cylindrical assemblies, these single-component solutions also seal all metal joints to eliminate the risk of fretting corrosion. They achieve 100% surface-to-surface contact, producing a cohesive, durable connection capable of withstanding vibration, extreme temperatures and chemical substances. RA-03 is a low viscosity, high strength anaerobic adhesive designed to retain cylindrical parts. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. This product is acceptable as a retaining compound in and around food processing areas according to NSF S5 (Registration No.163875). KEY FEATURES High strength Low viscosity High power transmission Resistance to dynamic loads Vibration resistant Recommended for gaps up to 0.15mm Corrosion prevention Single component DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding Cleaner and wait until fully evaporated. 2. If the cure speed is too slow on inactive metals, use Born2BondTM Anaerobic Activator. 3. For slip fitted parts, apply the adhesive around the pin and the inside of the collar and rotate during assembly to ensure fully coverage. 4. For press fitted parts, apply adhesive fully to both surfaces and assemble at high pressure. 5. For shrink fitted parts, the adhesive should be on the pin, the collar should be heated. 6. Parts should be fixed until sufficient handling strength is achieved. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Gear manufacturing Machine engineering Bearing assembly Drive shafts STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide TDS -
Bostik Born2Bond RA-20 Retaining Adhesive – 50 ml Bottle
$27.43 – $329.21Bostik Born2BondTM Retaining anaerobic adhesives are a cost effective, adaptable alternative or addition to mechanical retaining processes. Capable of bonding all types of cylindrical assemblies, these single-component solutions also seal all metal joints to eliminate the risk of fretting corrosion. They achieve 100% surface-to-surface contact, producing a cohesive, durable connection capable of withstanding vibration, extreme temperatures and chemical substances. RA-20 is a high viscosity, high strength anaerobic adhesive designed to retain cylindrical parts exposed to temperatures up to 230°C. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. KEY FEATURES High strength High viscosity High power transmission Resistance to dynamic loads Vibration resistant Corrosion prevention Recommended for gaps up to 0.2mm Single component Suitable for active and passive metals DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding Cleaner and wait until fully evaporated. 2. If the cure speed is too slow on inactive metals, use Born2BondTM Anaerobic Activator. 3. For slip fitted parts, apply the adhesive around the pin and the inside of the collar and rotate during assembly to ensure fully coverage. 4. For press fitted parts, apply adhesive fully to both surfaces and assemble at high pressure. 5. For shrink fitted parts, the adhesive should be on the pin, the collar should be heated. 6. Parts should be fixed until sufficient handling strength is achieved. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Gear manufacturing Machine engineering Bearing assembly Drive shafts STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide TDS -
Bostik Born2Bond RA-38 Retaining Adhesive – 50 ml Bottle
$26.55 – $318.59Bostik Born2BondTM Retaining anaerobic adhesives are a cost effective, adaptable alternative or addition to mechanical retaining processes. Capable of bonding all types of cylindrical assemblies, these single-component solutions also seal all metal joints to eliminate the risk of fretting corrosion. They achieve 100% surface-to-surface contact, producing a cohesive, durable connection capable of withstanding vibration, extreme temperatures and chemical substances. RA-38 is a medium viscosity, high strength anaerobic adhesive designed to retain cylindrical parts. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. KEY FEATURES High strength Medium viscosity High power transmission Resistance to dynamic loads Recommended for gaps up to 0.2mm Vibration resistant Corrosion prevention Single component Suitable for active and passive metals DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding Cleaner and wait until fully evaporated. 2. If the cure speed is too slow on inactive metals, use Born2BondTM Anaerobic Activator. 3. For slip fitted parts, apply the adhesive around the pin and the inside of the collar and rotate during assembly to ensure fully coverage. 4. For press fitted parts, apply adhesive fully to both surfaces and assemble at high pressure. 5. For shrink fitted parts, the adhesive should be on the pin, the collar should be heated. 6. Parts should be fixed until sufficient handling strength is achieved. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Gear manufacturing Machine engineering Bearing assembly Drive shafts STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide TDS -
Bostik Born2Bond RA-41 Retaining Adhesive – 50 ml Bottle
$26.55 – $318.59Bostik Born2BondTM Retaining anaerobic adhesives are a cost effective, adaptable alternative or addition to mechanical retaining processes. Capable of bonding all types of cylindrical assemblies, these single-component solutions also seal all metal joints to eliminate the risk of fretting corrosion. They achieve 100% surface-to-surface contact, producing a cohesive, durable connection capable of withstanding vibration, extreme temperatures and chemical substances. RA-41 is a medium viscosity, medium strength anaerobic adhesive designed to retain cylindrical parts. It is designed for service able assemblies like bearings of pumps. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. KEY FEATURES Medium strength Medium viscosity For servicable assemblies High power transmission Resistance to dynamic loads Recommended for gaps up to 0.1mm Vibration resistant Corrosion prevention Single component Suitable for active and passive metals DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding Cleaner and wait until fully evaporated. 2. If the cure speed is too slow on inactive metals, use Born2BondTM Anaerobic Activator. 3. For slip fitted parts, apply the adhesive around the pin and the inside of the collar and rotate during assembly to ensure fully coverage. 4. For press fitted parts, apply adhesive fully to both surfaces and assemble at high pressure. 5. For shrink fitted parts, the adhesive should be on the pin, the collar should be heated. 6. Parts should be fixed until sufficient handling strength is achieved. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Gear manufacturing Machine engineering Bearing assembly Drive shafts STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide TDS -
Bostik Born2Bond RA-48 Retaining Adhesive – 50 ml Bottle
$26.55 – $318.59Bostik Born2BondTM Retaining anaerobic adhesives are a cost effective, adaptable alternative or addition to mechanical retaining processes. Capable of bonding all types of cylindrical assemblies, these single-component solutions also seal all metal joints to eliminate the risk of fretting corrosion. They achieve 100% surface-to-surface contact, producing a cohesive, durable connection capable of withstanding vibration, extreme temperatures and chemical substances. RA-48 is a medium viscosity, high strength anaerobic adhesive designed to retain cylindrical parts. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. KEY FEATURES High strength Medium viscosity High power transmission Resistance to dynamic loads Recommended for gaps up to 0.15mm Vibration resistant Corrosion prevention Single component Suitable for active and passive metals DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding Cleaner and wait until fully evaporated. 2. If the cure speed is too slow on inactive metals, use Born2BondTM Anaerobic Activator. 3. For slip fitted parts, apply the adhesive around the pin and the inside of the collar and rotate during assembly to ensure fully coverage. 4. For press fitted parts, apply adhesive fully to both surfaces and assemble at high pressure. 5. For shrink fitted parts, the adhesive should be on the pin, the collar should be heated. 6. Parts should be fixed until sufficient handling strength is achieved. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Gear manufacturing Machine engineering Bearing assembly Drive shafts STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide TDS -
Bostik Born2Bond RA-60 Retaining Adhesive – 50 ml Bottle
$26.03 – $312.33Bostik Born2BondTM Retaining anaerobic adhesives are a cost effective, adaptable alternative or addition to mechanical retaining processes. Capable of bonding all types of cylindrical assemblies, these single-component solutions also seal all metal joints to eliminate the risk of fretting corrosion. They achieve 100% surface-to-surface contact, producing a cohesive, durable connection capable of withstanding vibration, extreme temperatures and chemical substances. RA-60 is a filled anaerobic retainer enabling repairs on worn-out parts. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. This product is acceptable as a retaining compound in and around food processing areas according to NSF S5 (Registration No.163877). KEY FEATURES High strength High viscosity / Paste High gap filling (up to 0.5mm) High power transmission Resistance to dynamic loads Vibration resistant Corrosion prevention Single component Suitable for active and passive metals DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding Cleaner and wait until fully evaporated. 2. If the cure speed is too slow on inactive metals, use Born2BondTM Anaerobic Activator. 3. For slip fitted parts, apply the adhesive around the pin and the inside of the collar and rotate during assembly to ensure fully coverage. 4. For press fitted parts, apply adhesive fully to both surfaces and assemble at high pressure. 5. For shrink fitted parts, the adhesive should be on the pin, the collar should be heated. 6. Parts should be fixed until sufficient handling strength is achieved. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Gear manufacturing Machine engineering Bearing assembly Drive shafts STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide TDS -
Bostik Born2Bond TA-22 Threadlocking Adhesive – 50 ml Bottle
$24.98 – $299.80Bostik Born2BondTM Threadlocking anaerobic adhesives provide single component, one-stop solutions for all threadlocking requirements, including preventive maintenance. Eliminating the cost and inconvenience of holding extensive inventory, these liquid adhesives fill and seal all voids to achieve a cohesive connection of metal parts that remains fixed even when subjected to extreme vibrations, temperatures or chemical substances. TA-22 is designed to lock and seal threaded fasteners which require easy disassembly with normal hand tools. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. This product is acceptable as a thread locking compound in and around food processing areas according to NSF S6 (Registration No.163870). KEY FEATURES Low strength Medium viscosity 100% connection - no loosening Evenly distribute force Vibration resistant Corrosion prevention Single component Suitable for active and passive metals Recommended for threads up to M20 DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding Cleaner and wait until fully evaporated. 2. If the cure speed is too slow, use Born2BondTM Anaerobic Activator. 3. Shake the product before use. 4. Apply adhesive onto threads. 5. Assemble and tighten as required. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Mechanical parts assembly Machine engineering Gear manufacturing Engines and powertrains STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide TDS -
Bostik Born2Bond TA-43 Threadlocking Adhesive – 1 lb Flat Top Can
$24.98 – $299.80Bostik Born2BondTM Threadlocking anaerobic adhesives provide single-component, one-stop solutions for all threadlocking requirements, including preventive maintenance. Eliminating the cost and inconvenience of holding extensive inventory, these liquid adhesives fill and seal all voids to achieve a cohesive connection of metal parts that remains fixed even when subjected to extreme vibrations, temperatures or chemical substances. TA-43 is a general purpose medium strength anaerobic adhesive designed to lock and seal threaded fasteners which require normal disassembly with standard hand tools. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. This product is acceptable as a thread locking compound in and around food processing areas according to NSF S6 (Registration No.163871). KEY FEATURES Medium strength Medium viscosity 100% connection - no loosening Evenly distribute force Vibration resistant Corrosion prevention Single component Suitable for active and passive metals Recommended for threads up to M36 DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding Cleaner and wait until fully evaporated. 2. If the cure speed is too slow, use Born2BondTM Anaerobic Activator. 3. Shake the product before use. 4. Apply adhesive onto threads. 5. Assemble and tighten as required. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Mechanical parts assembly Machine engineering Gear manufacturing Engines and powertrains STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide TDS -
Bostik Born2Bond TA-71 Threadlocking Adhesive – 50 ml Bottle
$24.98 – $299.80Bostik Born2BondTM Threadlocking anaerobic adhesives provide single-component, one-stop solutions for all threadlocking requirements, including preventive maintenance. Eliminating the cost and inconvenience of holding extensive inventory, these liquid adhesives fill and seal all voids to achieve a cohesive connecton of metal parts that remains fixed even when subjected to extreme vibrations, temperatures or chemical substances. TA-70 is a general purpose high strength anaerobic adhesive designed to lock and seal threaded fasteners which require permanent assembly. Once cured the product prevents leakage and/or loosening of parts from vibration and shock. This product is acceptable as a thread locking compound in and around food processing areas according to NSF S6 (Registration No.163872). KEY FEATURES High strength Medium viscosity 100% connection - no loosening Recommended for threads up to M20 Evenly distribute force Vibration resistant Corrosion prevention Single component Suitable for active and passive metals DIRECTIONS FOR USE 1. For best results, clean all surfaces (internal and external) with Born2BondTM Pre-Bonding Cleaner and wait until fully evaporated. 2. If the cure speed is too slow, use Born2BondTM Anaerobic Activator. 3. Shake the product before use. 4. Apply adhesive onto threads. 5. Assemble and tighten as required. METHOD OF USE Manual: Directly from the bottle with or without dispensing tips for more precise dispensing. Semi-Automated: Use of pressure-time systems for accurate volume and larger series. Full-Automated: fully automated robot or application lines APPLICATIONS Mechanical parts assembly Machine engineering Gear manufacturing Engines and powertrains STORAGE/SHELF LIFE Store product in the unopened container in a dry area out of direct sunlight. Storage below 7°C or greater than 28°C can adversely affect product performance. If stored properly, this product has a shelf life of 24 months. HEALTH/SAFETY The Safety Data Sheet is available on the Bostik website and should be consulted for proper handling, cleanup and spill containment before use. Keep containers covered to minimize contamination. LIMITATIONS This product is not recommended for use in pure oxygen and/or oxygen-rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Material removed from containers may be contaminated during use. Do not return product to the original container. Bostik will not assume responsibility for product that has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or customer service representative. MRO Solutions Guide