Lubriplate
Showing 1126–1167 of 1167 results
-
Lubriplate L1018-060 Synxtreme HT BN Max – Pail (5 gl)
$1,616.16Lubriplate L1018-060 Synxtreme HT BN Max - Pail (5 gl) NSF Registration -
Lubriplate L1018-062 Synxtreme HT BN Max – Drum (55 gal)
$17,568.98Lubriplate L1018-062 Synxtreme HT BN Max - Drum (55 gal) NSF Registration -
Lubriplate L1020-060 Bio-Synxtreme HF-32 – Pail (5 gl)
$311.74The LUBRIPLATE BIO-SYNXTREME HF Series are high performance hydraulic fluids designed for demanding industrial and marine (Vessel General Permit) applications requiring environmental sensitivity, water solubility, fire resistance, and excellent anti-wear properties over wide temperature ranges. These Polyalkylene glycol (PAG) based fluids, which are available in three viscosity grades, are anhydrous (water-free). LUBRIPLATE BIO-SYNXTREME Hydraulic Fluids do not break down to form sludge, and they do no hydrolyze in the presence of water. Furthermore, because of their high viscosity indices and excellent low temperature characteristics, one viscosity grade fluid may replace two or three viscosity grades. ADVANTAGES Excellent Anti-Wear Performance – Exceptional loadcarrying capabilities and specially formulated (with no zinc or other metal additives) to provide effective corrosion protection and anti-wear performance in hydraulic systems. Rated as antiwear (AW) fluids according to ASTM D7043 testing and FZG testing, which means the potential for greater operating reliability, less downtime, and lower maintenance costs. Clean, Long-Lasting Operation – When proper fluid and equipment maintenance procedures are followed, the BioSynxtreme HF series offer a long service life and operating reliability, lower maintenance costs, and reduced overall downtime. All Season Performance – High viscosity indices and low pour points, allowing year-round usage and eliminating seasonal changeovers. Biodegradability – Readily biodegradable according to OECD 301F. Non-Sheening – Does not cause a sheen or discoloration on the surface of the water or adjoining shorelines that would violate local water quality standards. Aquatic Toxicity – “Practically Non-Toxic” to fish and other aquatic wildlife according to the U.S. Fish and Wildlife Service hazard classification. Data Sheet -
Lubriplate L1020-062 Bio-Synxtreme HF-32 – Drum (55 gal)
$3,304.73The LUBRIPLATE BIO-SYNXTREME HF Series are high performance hydraulic fluids designed for demanding industrial and marine (Vessel General Permit) applications requiring environmental sensitivity, water solubility, fire resistance, and excellent anti-wear properties over wide temperature ranges. These Polyalkylene glycol (PAG) based fluids, which are available in three viscosity grades, are anhydrous (water-free). LUBRIPLATE BIO-SYNXTREME Hydraulic Fluids do not break down to form sludge, and they do no hydrolyze in the presence of water. Furthermore, because of their high viscosity indices and excellent low temperature characteristics, one viscosity grade fluid may replace two or three viscosity grades. ADVANTAGES Excellent Anti-Wear Performance – Exceptional loadcarrying capabilities and specially formulated (with no zinc or other metal additives) to provide effective corrosion protection and anti-wear performance in hydraulic systems. Rated as antiwear (AW) fluids according to ASTM D7043 testing and FZG testing, which means the potential for greater operating reliability, less downtime, and lower maintenance costs. Clean, Long-Lasting Operation – When proper fluid and equipment maintenance procedures are followed, the BioSynxtreme HF series offer a long service life and operating reliability, lower maintenance costs, and reduced overall downtime. All Season Performance – High viscosity indices and low pour points, allowing year-round usage and eliminating seasonal changeovers. Biodegradability – Readily biodegradable according to OECD 301F. Non-Sheening – Does not cause a sheen or discoloration on the surface of the water or adjoining shorelines that would violate local water quality standards. Aquatic Toxicity – “Practically Non-Toxic” to fish and other aquatic wildlife according to the U.S. Fish and Wildlife Service hazard classification. Data Sheet -
Lubriplate L1021-060 Bio-Synxtreme HF-46 – Pail (5 gl)
$311.74The LUBRIPLATE BIO-SYNXTREME HF Series are high performance hydraulic fluids designed for demanding industrial and marine (Vessel General Permit) applications requiring environmental sensitivity, water solubility, fire resistance, and excellent anti-wear properties over wide temperature ranges. These Polyalkylene glycol (PAG) based fluids, which are available in three viscosity grades, are anhydrous (water-free). LUBRIPLATE BIO-SYNXTREME Hydraulic Fluids do not break down to form sludge, and they do no hydrolyze in the presence of water. Furthermore, because of their high viscosity indices and excellent low temperature characteristics, one viscosity grade fluid may replace two or three viscosity grades. ADVANTAGES Excellent Anti-Wear Performance – Exceptional loadcarrying capabilities and specially formulated (with no zinc or other metal additives) to provide effective corrosion protection and anti-wear performance in hydraulic systems. Rated as antiwear (AW) fluids according to ASTM D7043 testing and FZG testing, which means the potential for greater operating reliability, less downtime, and lower maintenance costs. Clean, Long-Lasting Operation – When proper fluid and equipment maintenance procedures are followed, the BioSynxtreme HF series offer a long service life and operating reliability, lower maintenance costs, and reduced overall downtime. All Season Performance – High viscosity indices and low pour points, allowing year-round usage and eliminating seasonal changeovers. Biodegradability – Readily biodegradable according to OECD 301F. Non-Sheening – Does not cause a sheen or discoloration on the surface of the water or adjoining shorelines that would violate local water quality standards. Aquatic Toxicity – “Practically Non-Toxic” to fish and other aquatic wildlife according to the U.S. Fish and Wildlife Service hazard classification. Data Sheet -
Lubriplate L1021-062 Bio-Synxtreme HF-46 – Drum (55 gal)
$3,304.73The LUBRIPLATE BIO-SYNXTREME HF Series are high performance hydraulic fluids designed for demanding industrial and marine (Vessel General Permit) applications requiring environmental sensitivity, water solubility, fire resistance, and excellent anti-wear properties over wide temperature ranges. These Polyalkylene glycol (PAG) based fluids, which are available in three viscosity grades, are anhydrous (water-free). LUBRIPLATE BIO-SYNXTREME Hydraulic Fluids do not break down to form sludge, and they do no hydrolyze in the presence of water. Furthermore, because of their high viscosity indices and excellent low temperature characteristics, one viscosity grade fluid may replace two or three viscosity grades. ADVANTAGES Excellent Anti-Wear Performance – Exceptional loadcarrying capabilities and specially formulated (with no zinc or other metal additives) to provide effective corrosion protection and anti-wear performance in hydraulic systems. Rated as antiwear (AW) fluids according to ASTM D7043 testing and FZG testing, which means the potential for greater operating reliability, less downtime, and lower maintenance costs. Clean, Long-Lasting Operation – When proper fluid and equipment maintenance procedures are followed, the BioSynxtreme HF series offer a long service life and operating reliability, lower maintenance costs, and reduced overall downtime. All Season Performance – High viscosity indices and low pour points, allowing year-round usage and eliminating seasonal changeovers. Biodegradability – Readily biodegradable according to OECD 301F. Non-Sheening – Does not cause a sheen or discoloration on the surface of the water or adjoining shorelines that would violate local water quality standards. Aquatic Toxicity – “Practically Non-Toxic” to fish and other aquatic wildlife according to the U.S. Fish and Wildlife Service hazard classification. Data Sheet -
Lubriplate L1022-060 Bio-Synxtreme HF-68 – Pail (5 gl)
$311.74The LUBRIPLATE BIO-SYNXTREME HF Series are high performance hydraulic fluids designed for demanding industrial and marine (Vessel General Permit) applications requiring environmental sensitivity, water solubility, fire resistance, and excellent anti-wear properties over wide temperature ranges. These Polyalkylene glycol (PAG) based fluids, which are available in three viscosity grades, are anhydrous (water-free). LUBRIPLATE BIO-SYNXTREME Hydraulic Fluids do not break down to form sludge, and they do no hydrolyze in the presence of water. Furthermore, because of their high viscosity indices and excellent low temperature characteristics, one viscosity grade fluid may replace two or three viscosity grades. ADVANTAGES Excellent Anti-Wear Performance – Exceptional loadcarrying capabilities and specially formulated (with no zinc or other metal additives) to provide effective corrosion protection and anti-wear performance in hydraulic systems. Rated as antiwear (AW) fluids according to ASTM D7043 testing and FZG testing, which means the potential for greater operating reliability, less downtime, and lower maintenance costs. Clean, Long-Lasting Operation – When proper fluid and equipment maintenance procedures are followed, the BioSynxtreme HF series offer a long service life and operating reliability, lower maintenance costs, and reduced overall downtime. All Season Performance – High viscosity indices and low pour points, allowing year-round usage and eliminating seasonal changeovers. Biodegradability – Readily biodegradable according to OECD 301F. Non-Sheening – Does not cause a sheen or discoloration on the surface of the water or adjoining shorelines that would violate local water quality standards. Aquatic Toxicity – “Practically Non-Toxic” to fish and other aquatic wildlife according to the U.S. Fish and Wildlife Service hazard classification. Data Sheet -
Lubriplate L1022-062 Bio-Synxtreme HF-68 – Drum (55 gal)
$3,304.73The LUBRIPLATE BIO-SYNXTREME HF Series are high performance hydraulic fluids designed for demanding industrial and marine (Vessel General Permit) applications requiring environmental sensitivity, water solubility, fire resistance, and excellent anti-wear properties over wide temperature ranges. These Polyalkylene glycol (PAG) based fluids, which are available in three viscosity grades, are anhydrous (water-free). LUBRIPLATE BIO-SYNXTREME Hydraulic Fluids do not break down to form sludge, and they do no hydrolyze in the presence of water. Furthermore, because of their high viscosity indices and excellent low temperature characteristics, one viscosity grade fluid may replace two or three viscosity grades. ADVANTAGES Excellent Anti-Wear Performance – Exceptional loadcarrying capabilities and specially formulated (with no zinc or other metal additives) to provide effective corrosion protection and anti-wear performance in hydraulic systems. Rated as antiwear (AW) fluids according to ASTM D7043 testing and FZG testing, which means the potential for greater operating reliability, less downtime, and lower maintenance costs. Clean, Long-Lasting Operation – When proper fluid and equipment maintenance procedures are followed, the BioSynxtreme HF series offer a long service life and operating reliability, lower maintenance costs, and reduced overall downtime. All Season Performance – High viscosity indices and low pour points, allowing year-round usage and eliminating seasonal changeovers. Biodegradability – Readily biodegradable according to OECD 301F. Non-Sheening – Does not cause a sheen or discoloration on the surface of the water or adjoining shorelines that would violate local water quality standards. Aquatic Toxicity – “Practically Non-Toxic” to fish and other aquatic wildlife according to the U.S. Fish and Wildlife Service hazard classification. Data Sheet -
Lubriplate L1023-060 Synxtreme FRHD-46 – Pail (5 gl)
$262.80Lubriplate L1023-060 Synxtreme FRHD-46 - Pail (5 gl) -
Lubriplate L1023-062 Synxtreme FRHD-46 – Drum (55 gal)
$2,774.20Lubriplate L1023-062 Synxtreme FRHD-46 - Drum (55 gal) -
Lubriplate L1023-072 Synxtreme FRHD-46 – Passport Bin (275 gal)
$13,785.20Lubriplate L1023-072 Synxtreme FRHD-46 - Passport Bin (275 gal) -
Lubriplate L1024-060 Synxtreme FRH1-46 – Pail (5 gl)
$310.57LUBRIPLATE SYNXTREME FRH1-46 is a high performance hydraulic fluid designed for demanding industrial and food processing applications requiring fire resistance, and excellent anti-wear properties over wide temperature ranges. This product complies with CFR 21, section 178.3570. APPLICATIONS Excellent Anti-Wear Performance – Exceptional loadcarrying capabilities and specially formulated to provide effective corrosion protection and anti-wear performance in hydraulic systems. Rated as anti-wear, which means the potential for greater reliability, less downtime, and lower maintenance costs. Fire Resistance – High flash and fire points provide safety in applications calling for fire resistant fluids, thus providing operating confidence and potentially reduced insurance costs. FM approved, using FM test method 6930, has classified HF 46 Hydraulic Fluid as “Approved Industrial Fluids”. Biodegradability – Readily biodegradable according to OECD 301F COMPATIBILITY Other Hydraulic Fluids – It is compatible with hydrocarbon-based hydraulic fluids. As with any fluid conversion, recognized industry procedures including system cleanup and flushing should be followed. Elastomers – Suitable for use with many elastomeric materials used in seals and gaskets. Compatible elastomers are: Viton, Kalrez, Silicone, Polysulfide, EPR, Butyl Rubber, Buna N, Fluoraz, EPDM, Natural Black Rubber, Natural Red Rubber and Aflas. Plastics – Compatibility should be assessed for any plastic components (such as reservoir sight glasses) exposed to a hydraulic fluid. Paints – Ester based fluids show some solvency for common oil-based paints but minimal solvency for many epoxy-based paints Data Sheet NSF Food-Grade Registrations -
Lubriplate L1024-062 Synxtreme FRH1-46 – Drum (55 gal)
$3,278.28LUBRIPLATE SYNXTREME FRH1-46 is a high performance hydraulic fluid designed for demanding industrial and food processing applications requiring fire resistance, and excellent anti-wear properties over wide temperature ranges. This product complies with CFR 21, section 178.3570. APPLICATIONS Excellent Anti-Wear Performance – Exceptional loadcarrying capabilities and specially formulated to provide effective corrosion protection and anti-wear performance in hydraulic systems. Rated as anti-wear, which means the potential for greater reliability, less downtime, and lower maintenance costs. Fire Resistance – High flash and fire points provide safety in applications calling for fire resistant fluids, thus providing operating confidence and potentially reduced insurance costs. FM approved, using FM test method 6930, has classified HF 46 Hydraulic Fluid as “Approved Industrial Fluids”. Biodegradability – Readily biodegradable according to OECD 301F COMPATIBILITY Other Hydraulic Fluids – It is compatible with hydrocarbon-based hydraulic fluids. As with any fluid conversion, recognized industry procedures including system cleanup and flushing should be followed. Elastomers – Suitable for use with many elastomeric materials used in seals and gaskets. Compatible elastomers are: Viton, Kalrez, Silicone, Polysulfide, EPR, Butyl Rubber, Buna N, Fluoraz, EPDM, Natural Black Rubber, Natural Red Rubber and Aflas. Plastics – Compatibility should be assessed for any plastic components (such as reservoir sight glasses) exposed to a hydraulic fluid. Paints – Ester based fluids show some solvency for common oil-based paints but minimal solvency for many epoxy-based paints Data Sheet NSF Food-Grade Registrations -
Lubriplate L1027-060 Bio-Synxtreme EGO-150 – Pail (5 gl)
$507.91LUBRIPLATE Biosynxtreme EGO-150 is a biodegradable synthetic gear oil which is designed to be used in environmentally sensitive areas where the most demanding operating conditions are expected. APPLICATIONS LUBRIPLATE Biosynxtreme EGO-150 Gear Oil may be recommended for helical, bevel helical, planetary and worm gear reducers. ADVANTAGES LUBRIPLATE Biosynxtreme EGO-150 delivers outstanding protection against abrasion and wear. It delivers unsurpassed extreme pressure and anti-wear performance and provides good thermal stability. Biosynxtreme EGO-150 is Ultimately Biodegradable (Pw1) per ASTM D-5864. RECOMMENDATIONS LUBRIPLATE Biosynxtreme EGO-150 is ideal for applications where exposure to the environment is expected. It replaces all petroleum and synthetic lubricants for a wide variety of gear box configurations. Data Sheet -
Lubriplate L1027-062 Bio-Synxtreme EGO-150 – Drum (55 gal)
$5,418.27LUBRIPLATE Biosynxtreme EGO-150 is a biodegradable synthetic gear oil which is designed to be used in environmentally sensitive areas where the most demanding operating conditions are expected. APPLICATIONS LUBRIPLATE Biosynxtreme EGO-150 Gear Oil may be recommended for helical, bevel helical, planetary and worm gear reducers. ADVANTAGES LUBRIPLATE Biosynxtreme EGO-150 delivers outstanding protection against abrasion and wear. It delivers unsurpassed extreme pressure and anti-wear performance and provides good thermal stability. Biosynxtreme EGO-150 is Ultimately Biodegradable (Pw1) per ASTM D-5864. RECOMMENDATIONS LUBRIPLATE Biosynxtreme EGO-150 is ideal for applications where exposure to the environment is expected. It replaces all petroleum and synthetic lubricants for a wide variety of gear box configurations. Data Sheet -
Lubriplate L1030-060 Bio-Synxtreme EGO-150 – Pail (5 gl)
$399.17LUBRIPLATE SYNCOMP AN-46 is an ISO 46 alkylated naphthalene based, oxidation resistant lubricant designed to provide high temperature and long-term lubrication with minimal deposit formation ADVANTAGES Wide operating temperature range Fewer oil changes Lower oil consumption Reduces compressor maintenance Eliminates lacquering and deposits Greatly reduces fire and explosion hazard Superior performance and longer oil life vs. PAO synthetic fluids Fully compatible with PAO fluids NSF H1 Food Grade Registered No. 160052 APPLICATIONS Oil flooded rotary screw compressors Oil flooded rotary vane compressors LUBRIPLATE SYNCOMP AN-46 may also be considered for other applications requiring an oxidation resistant lubricant. Nominal Operating Range is -25°C to 230°C Data Sheet NSF Registration -
Lubriplate L1030-062 Bio-Synxtreme EGO-150 – Drum (55 gal)
$4,233.52LUBRIPLATE SYNCOMP AN-46 is an ISO 46 alkylated naphthalene based, oxidation resistant lubricant designed to provide high temperature and long-term lubrication with minimal deposit formation ADVANTAGES Wide operating temperature range Fewer oil changes Lower oil consumption Reduces compressor maintenance Eliminates lacquering and deposits Greatly reduces fire and explosion hazard Superior performance and longer oil life vs. PAO synthetic fluids Fully compatible with PAO fluids NSF H1 Food Grade Registered No. 160052 APPLICATIONS Oil flooded rotary screw compressors Oil flooded rotary vane compressors LUBRIPLATE SYNCOMP AN-46 may also be considered for other applications requiring an oxidation resistant lubricant. Nominal Operating Range is -25°C to 230°C Data Sheet NSF Registration -
Lubriplate L1040-060 Synxtreme FRH1-46Z – Pail (5 gl)
$310.57Lubriplate L1040-060 Synxtreme FRH1-46Z - Pail (5 gl) -
Lubriplate L1040-062 Synxtreme FRH1-46Z – Drum (55 gal)
$3,278.28Lubriplate L1040-062 Synxtreme FRH1-46Z - Drum (55 gal) -
Lubriplate L1040-072 Synxtreme FRH1-46Z – Passport Bin (275 gal)
$13,785.20Lubriplate L1040-072 Synxtreme FRH1-46Z - Passport Bin (275 gal) -
Lubriplate L1041-060 Synxtreme FRHD-46Z – Pail (5 gl)
$262.80Lubriplate L1041-060 Synxtreme FRHD-46Z - Pail (5 gl) -
Lubriplate L1041-062 Synxtreme FRHD-46Z – Drum (55 gal)
$2,774.20Lubriplate L1041-062 Synxtreme FRHD-46Z - Drum (55 gal) -
Lubriplate L1041-072 Synxtreme FRHD-46Z – Passport Bin (275 gal)
$13,785.20Lubriplate L1041-072 Synxtreme FRHD-46Z - Passport Bin (275 gal) -
Lubriplate L1050-060 Biobased Green Hydraulic Oil 32 – Pail (5 gl)
$266.37LUBRIPLATE Biobased Green Hydraulic Fluids are ultimately biodegradable1 vegetable based formulas that replace mineral oil based hydraulic fluids. They are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam and demulsibility properties. They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas). Zinc-free additive systems have also been developed that are environmentally friendly and meet or exceed pump requirements. LUBRIPLATE Biobased Green Hydraulic Fluids are designed for use in mobile and stationary hydraulic vane, piston and gear-type pumps and have shown to have exceptional anti-wear performance. Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S) and V-104C (ASTM D-2882) pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 150º to 210ºF. The anti-wear performance exceeds the requirements for US Steel 126 and 127, load stage 10 in the FZG (DIN 51354), DIN 51524 and GM (LS-2). They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges. These fluids meet or exceed Federal Specification A-A59354 Superseding MIL-H-46001D. LUBRIPLATE Biobased Green Hydraulic Fluids should be used in hydraulic systems where low toxicity and BIODEGRADABILITY properties are required. Base oils and additives in these products pass and exceed the acute toxicity (LC-50) criteria adopted by the US Fish and Wildlife Service and the US EPA. LUBRIPLATE Biobased Green Hydraulic Fluids are ENVIRONMENTALLY RESPONSIBLE lubricants that are formulated from renewable agricultural plant resources. Data Sheet -
Lubriplate L1050-062 Biobased Green Hydraulic Oil 32 – Drum (55 gal)
$2,812.81LUBRIPLATE Biobased Green Hydraulic Fluids are ultimately biodegradable1 vegetable based formulas that replace mineral oil based hydraulic fluids. They are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam and demulsibility properties. They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas). Zinc-free additive systems have also been developed that are environmentally friendly and meet or exceed pump requirements. LUBRIPLATE Biobased Green Hydraulic Fluids are designed for use in mobile and stationary hydraulic vane, piston and gear-type pumps and have shown to have exceptional anti-wear performance. Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S) and V-104C (ASTM D-2882) pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 150º to 210ºF. The anti-wear performance exceeds the requirements for US Steel 126 and 127, load stage 10 in the FZG (DIN 51354), DIN 51524 and GM (LS-2). They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges. These fluids meet or exceed Federal Specification A-A59354 Superseding MIL-H-46001D. LUBRIPLATE Biobased Green Hydraulic Fluids should be used in hydraulic systems where low toxicity and BIODEGRADABILITY properties are required. Base oils and additives in these products pass and exceed the acute toxicity (LC-50) criteria adopted by the US Fish and Wildlife Service and the US EPA. LUBRIPLATE Biobased Green Hydraulic Fluids are ENVIRONMENTALLY RESPONSIBLE lubricants that are formulated from renewable agricultural plant resources. Data Sheet -
Lubriplate L1051-060 Biobased Green Hydraulic Oil 46 – Pail (5 gl)
$266.37LUBRIPLATE Biobased Green Hydraulic Fluids are ultimately biodegradable1 vegetable based formulas that replace mineral oil based hydraulic fluids. They are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam and demulsibility properties. They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas). Zinc-free additive systems have also been developed that are environmentally friendly and meet or exceed pump requirements. LUBRIPLATE Biobased Green Hydraulic Fluids are designed for use in mobile and stationary hydraulic vane, piston and gear-type pumps and have shown to have exceptional anti-wear performance. Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S) and V-104C (ASTM D-2882) pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 150º to 210ºF. The anti-wear performance exceeds the requirements for US Steel 126 and 127, load stage 10 in the FZG (DIN 51354), DIN 51524 and GM (LS-2). They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges. These fluids meet or exceed Federal Specification A-A59354 Superseding MIL-H-46001D. LUBRIPLATE Biobased Green Hydraulic Fluids should be used in hydraulic systems where low toxicity and BIODEGRADABILITY properties are required. Base oils and additives in these products pass and exceed the acute toxicity (LC-50) criteria adopted by the US Fish and Wildlife Service and the US EPA. LUBRIPLATE Biobased Green Hydraulic Fluids are ENVIRONMENTALLY RESPONSIBLE lubricants that are formulated from renewable agricultural plant resources. Data Sheet -
Lubriplate L1051-062 Biobased Green Hydraulic Oil 46 – Drum (55 gal)
$2,812.81LUBRIPLATE Biobased Green Hydraulic Fluids are ultimately biodegradable1 vegetable based formulas that replace mineral oil based hydraulic fluids. They are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam and demulsibility properties. They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas). Zinc-free additive systems have also been developed that are environmentally friendly and meet or exceed pump requirements. LUBRIPLATE Biobased Green Hydraulic Fluids are designed for use in mobile and stationary hydraulic vane, piston and gear-type pumps and have shown to have exceptional anti-wear performance. Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S) and V-104C (ASTM D-2882) pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 150º to 210ºF. The anti-wear performance exceeds the requirements for US Steel 126 and 127, load stage 10 in the FZG (DIN 51354), DIN 51524 and GM (LS-2). They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges. These fluids meet or exceed Federal Specification A-A59354 Superseding MIL-H-46001D. LUBRIPLATE Biobased Green Hydraulic Fluids should be used in hydraulic systems where low toxicity and BIODEGRADABILITY properties are required. Base oils and additives in these products pass and exceed the acute toxicity (LC-50) criteria adopted by the US Fish and Wildlife Service and the US EPA. LUBRIPLATE Biobased Green Hydraulic Fluids are ENVIRONMENTALLY RESPONSIBLE lubricants that are formulated from renewable agricultural plant resources. Data Sheet -
Lubriplate L1052-060 Biobased Green Hydraulic Oil 68 – Pail (5 gl)
$266.37LUBRIPLATE Biobased Green Hydraulic Fluids are ultimately biodegradable1 vegetable based formulas that replace mineral oil based hydraulic fluids. They are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam and demulsibility properties. They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas). Zinc-free additive systems have also been developed that are environmentally friendly and meet or exceed pump requirements. LUBRIPLATE Biobased Green Hydraulic Fluids are designed for use in mobile and stationary hydraulic vane, piston and gear-type pumps and have shown to have exceptional anti-wear performance. Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S) and V-104C (ASTM D-2882) pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 150º to 210ºF. The anti-wear performance exceeds the requirements for US Steel 126 and 127, load stage 10 in the FZG (DIN 51354), DIN 51524 and GM (LS-2). They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges. These fluids meet or exceed Federal Specification A-A59354 Superseding MIL-H-46001D. LUBRIPLATE Biobased Green Hydraulic Fluids should be used in hydraulic systems where low toxicity and BIODEGRADABILITY properties are required. Base oils and additives in these products pass and exceed the acute toxicity (LC-50) criteria adopted by the US Fish and Wildlife Service and the US EPA. LUBRIPLATE Biobased Green Hydraulic Fluids are ENVIRONMENTALLY RESPONSIBLE lubricants that are formulated from renewable agricultural plant resources. Data Sheet -
Lubriplate L1052-062 Biobased Green Hydraulic Oil 68 – Drum (55 gal)
$2,812.81LUBRIPLATE Biobased Green Hydraulic Fluids are ultimately biodegradable1 vegetable based formulas that replace mineral oil based hydraulic fluids. They are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam and demulsibility properties. They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas). Zinc-free additive systems have also been developed that are environmentally friendly and meet or exceed pump requirements. LUBRIPLATE Biobased Green Hydraulic Fluids are designed for use in mobile and stationary hydraulic vane, piston and gear-type pumps and have shown to have exceptional anti-wear performance. Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S) and V-104C (ASTM D-2882) pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 150º to 210ºF. The anti-wear performance exceeds the requirements for US Steel 126 and 127, load stage 10 in the FZG (DIN 51354), DIN 51524 and GM (LS-2). They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges. These fluids meet or exceed Federal Specification A-A59354 Superseding MIL-H-46001D. LUBRIPLATE Biobased Green Hydraulic Fluids should be used in hydraulic systems where low toxicity and BIODEGRADABILITY properties are required. Base oils and additives in these products pass and exceed the acute toxicity (LC-50) criteria adopted by the US Fish and Wildlife Service and the US EPA. LUBRIPLATE Biobased Green Hydraulic Fluids are ENVIRONMENTALLY RESPONSIBLE lubricants that are formulated from renewable agricultural plant resources. Data Sheet -
Lubriplate L1072-060 UTF Biobased Green – Pail (5 gl)
$493.87LUBRIPLATE UTF Biobased Green is a universal tractor fluid that incorporates Stabilized* additive technology with biodegradable vegetable based stocks. This formulation contains special frictional modifiers for the Wet Brake’s equipment design and is compounded with detergent, dispersant, anti-wear, anti-rust and anti-foam inhibitors. LUBRIPLATE UTF Biobased Green is an ultimately biodegradable, multi-grade lubricant that can be used in agricultural, industrial and construction equipment and has proven field performance. ADVANTAGES LUBRIPLATE UTF Biobased Green is an ENVIRONMENTALLY RESPONSIBLE hydraulic fluid that is formulated from renewable, agricultural plant resources. We believe Earth’s environmental future rests in the use of renewable materials. High Oleic Base Stocks (HOBS) are agricultural vegetable oils. This Stabilized technology allows the HOBS to perform as a high performance formula in high and low temperature applications, reducing oil thickening and deposits. APPLICATIONS Meets or exceeds all of the requirements of John Deere’s Hygard (Specification J20-C); Allison C-3, Cat TO-2 and API GL-4, Low-Speed/High Torque. Data Sheet -
Lubriplate L1072-062 UTF Biobased Green – Drum (55 gal)
$5,311.02LUBRIPLATE UTF Biobased Green is a universal tractor fluid that incorporates Stabilized* additive technology with biodegradable vegetable based stocks. This formulation contains special frictional modifiers for the Wet Brake’s equipment design and is compounded with detergent, dispersant, anti-wear, anti-rust and anti-foam inhibitors. LUBRIPLATE UTF Biobased Green is an ultimately biodegradable, multi-grade lubricant that can be used in agricultural, industrial and construction equipment and has proven field performance. ADVANTAGES LUBRIPLATE UTF Biobased Green is an ENVIRONMENTALLY RESPONSIBLE hydraulic fluid that is formulated from renewable, agricultural plant resources. We believe Earth’s environmental future rests in the use of renewable materials. High Oleic Base Stocks (HOBS) are agricultural vegetable oils. This Stabilized technology allows the HOBS to perform as a high performance formula in high and low temperature applications, reducing oil thickening and deposits. APPLICATIONS Meets or exceeds all of the requirements of John Deere’s Hygard (Specification J20-C); Allison C-3, Cat TO-2 and API GL-4, Low-Speed/High Torque. Data Sheet -
Lubriplate L1073-060 SCL-H1/220 – Pail (5 gl)
$366.67LUBRIPLATE SCL-H1/220 is a unique combination of synthetic fluids specifically designed for use on oven chains and other industrial bearing and gear applications in which high temperatures are encountered. The combination of an ashless additive system and a synthetic ester base provide protection against wear, rust, oxidation and corrosion. Both fluids utilize an enhanced coefficient of friction additive which will disperse and clean pre-existing carbon deposits on chains and bearings thereby reducing power consumption. This product delivers unsurpassed oxidation stability. Fluid Type: synthetic ISO Grade: 220 Food Grade - NSF H1: Yes NSF Registration -
Lubriplate L1073-062 SCL-H1/220 – Drum (55 gal)
$3,871.01LUBRIPLATE SCL-H1/220 is a unique combination of synthetic fluids specifically designed for use on oven chains and other industrial bearing and gear applications in which high temperatures are encountered. The combination of an ashless additive system and a synthetic ester base provide protection against wear, rust, oxidation and corrosion. Both fluids utilize an enhanced coefficient of friction additive which will disperse and clean pre-existing carbon deposits on chains and bearings thereby reducing power consumption. This product delivers unsurpassed oxidation stability. Fluid Type: synthetic ISO Grade: 220 Food Grade - NSF H1: Yes NSF Registration -
Lubriplate L1075-060 SCL-HD/220 – Pail (5 gl)
$348.99LUBRIPLATE SCL-HD Series are unique combinations of synthetic fluids specifically designed for use on oven chains and other industrial bearing and gear applications in which high temperatures are encountered. The combination of an ashless additive system and a synthetic ester base provide protection against wear, rust, oxidation and corrosion. Both fluids utilize an enhanced coefficient of friction additive which will disperse and clean pre-existing carbon deposits on chains and bearings thereby reducing power consumption. These products deliverunsurpassed oxidation stability. ADVANTAGES Reduces carbon build-up on chains No harmful VOC’s which pollute the atmosphere Advanced unique chemistry reduces friction, wear and energy costs High auto-ignition temperature to reduce the risk of oven fires Superior film strength reduces oil consumption and reduces smoke APPLICATIONS Major applications include: Drying Ovens Textile - Tenter Frame Chains Wallboard - Dryer Chains Painting - Dryer Chains Lithographic Chains - Beverage Can Lines Glass - Forming Line Chains Laminating - Drying Lines Food Cookers & Frying Heat Treating - Chains & Bearings Kiln Support Rollers - Cement Plants (Trunions) Bakery Oven Chains Data Sheet -
Lubriplate L1075-062 SCL-HD/220 – Drum (55 gal)
$3,677.25LUBRIPLATE SCL-HD Series are unique combinations of synthetic fluids specifically designed for use on oven chains and other industrial bearing and gear applications in which high temperatures are encountered. The combination of an ashless additive system and a synthetic ester base provide protection against wear, rust, oxidation and corrosion. Both fluids utilize an enhanced coefficient of friction additive which will disperse and clean pre-existing carbon deposits on chains and bearings thereby reducing power consumption. These products deliverunsurpassed oxidation stability. ADVANTAGES Reduces carbon build-up on chains No harmful VOC’s which pollute the atmosphere Advanced unique chemistry reduces friction, wear and energy costs High auto-ignition temperature to reduce the risk of oven fires Superior film strength reduces oil consumption and reduces smoke APPLICATIONS Major applications include: Drying Ovens Textile - Tenter Frame Chains Wallboard - Dryer Chains Painting - Dryer Chains Lithographic Chains - Beverage Can Lines Glass - Forming Line Chains Laminating - Drying Lines Food Cookers & Frying Heat Treating - Chains & Bearings Kiln Support Rollers - Cement Plants (Trunions) Bakery Oven Chains Data Sheet -
Lubriplate L1076-060 SCL-HD/68 – Pail (5 gl)
$443.24LUBRIPLATE SCL-HD Series are unique combinations of synthetic fluids specifically designed for use on oven chains and other industrial bearing and gear applications in which high temperatures are encountered. The combination of an ashless additive system and a synthetic ester base provide protection against wear, rust, oxidation and corrosion. Both fluids utilize an enhanced coefficient of friction additive which will disperse and clean pre-existing carbon deposits on chains and bearings thereby reducing power consumption. These products deliverunsurpassed oxidation stability. ADVANTAGES Reduces carbon build-up on chains No harmful VOC’s which pollute the atmosphere Advanced unique chemistry reduces friction, wear and energy costs High auto-ignition temperature to reduce the risk of oven fires Superior film strength reduces oil consumption and reduces smoke APPLICATIONS Major applications include: Drying Ovens Textile - Tenter Frame Chains Wallboard - Dryer Chains Painting - Dryer Chains Lithographic Chains - Beverage Can Lines Glass - Forming Line Chains Laminating - Drying Lines Food Cookers & Frying Heat Treating - Chains & Bearings Kiln Support Rollers - Cement Plants (Trunions) Bakery Oven Chains Data Sheet -
Lubriplate L1076-062 SCL-HD/68 – Drum (55 gal)
$4,670.38LUBRIPLATE SCL-HD Series are unique combinations of synthetic fluids specifically designed for use on oven chains and other industrial bearing and gear applications in which high temperatures are encountered. The combination of an ashless additive system and a synthetic ester base provide protection against wear, rust, oxidation and corrosion. Both fluids utilize an enhanced coefficient of friction additive which will disperse and clean pre-existing carbon deposits on chains and bearings thereby reducing power consumption. These products deliverunsurpassed oxidation stability. ADVANTAGES Reduces carbon build-up on chains No harmful VOC’s which pollute the atmosphere Advanced unique chemistry reduces friction, wear and energy costs High auto-ignition temperature to reduce the risk of oven fires Superior film strength reduces oil consumption and reduces smoke APPLICATIONS Major applications include: Drying Ovens Textile - Tenter Frame Chains Wallboard - Dryer Chains Painting - Dryer Chains Lithographic Chains - Beverage Can Lines Glass - Forming Line Chains Laminating - Drying Lines Food Cookers & Frying Heat Treating - Chains & Bearings Kiln Support Rollers - Cement Plants (Trunions) Bakery Oven Chains Data Sheet -
Lubriplate No. 0
Price range: $228.41 through $2,350.40LUBRIPLATE FLUID PRODUCTS are specially compounded for a wide variety of industrial uses. LUBRIPLATE fluids’ performance and economy greatly exceed that of conventional oils. They impart a unique load-carrying film, exceptional lubricity and anti-friction properties not found in conventional oils of the same viscosity. The high-wetting nature of these lubricants provide superior protective coating of the metals. LUBRIPLATE No. 0 is a light 5W type of oil for extremely high speed applications (up to 25,000 rpm) such as spindle lubrication and grinder arbor bearings. Also makes an excellent lamination oil for progressive stamping operations. Data Sheet -
Lubriplate No. 1
Price range: $228.41 through $2,438.54LUBRIPLATE FLUID PRODUCTS are specially compounded for a wide variety of industrial uses. LUBRIPLATE fluids’ performance and economy greatly exceed that of conventional oils. They impart a unique load-carrying film, exceptional lubricity and anti-friction properties not found in conventional oils of the same viscosity. The high-wetting nature of these lubricants provide superior protective coating of the metals. LUBRIPLATE No. 1 is a light 10W type of oil for textile spindles, grinder arbors and other types of bearings operating at high speeds. Excellent cold test makes this an ideal extreme low temperature hydraulic fluid. Data Sheet -
Lubriplate No. 2
Price range: $228.41 through $2,438.54LUBRIPLATE FLUID PRODUCTS are specially compounded for a wide variety of industrial uses. LUBRIPLATE fluids’ performance and economy greatly exceed that of conventional oils. They impart a unique load-carrying film, exceptional lubricity and anti-friction properties not found in conventional oils of the same viscosity. The high-wetting nature of these lubricants provide superior protective coating of the metals. LUBRIPLATE No. 2 is a 20 weight type oil for light general oil applications. Excellent for ring oiled bearings, wick feeds, bottle and air-line oilers, oil cups, light circulating systems, enclosed chains, etc. Data Sheet -
Lubriplate No. 3-V
Price range: $228.41 through $2,438.54LUBRIPLATE FLUID PRODUCTS are specially compounded for a wide variety of industrial uses. LUBRIPLATE fluids’ performance and economy greatly exceed that of conventional oils. They impart a unique load-carrying film, exceptional lubricity and anti-friction properties not found in conventional oils of the same viscosity. The high-wetting nature of these lubricants provide superior protective coating of the metals. LUBRIPLATE No. 3-V is a 20 weight oil especially designed for combination machine tool way lubrication and bearing lubrication. Excellent for ring oiled bearings, oil cups, circulating systems and Servo Controlled Machine Tools. Meets the majority of machine tool manufacturers’ recommendations for general machine oil type lubrication. Contains a tackiness additive. Data Sheet -
Lubriplate No. 4
Price range: $228.41 through $2,438.54LUBRIPLATE No. 4 and LUBRIPLATE No. 8 are specially (formulated oils) strictly for industrial bearing and gear case applications. These oils are formulated with special lubricity agents and tackiness additives. LUBRIPLATE No. 4 and LUBRIPLATE No. 8 have exceptional film strength, and "stay put" or "clinging" qualities. These oils also provide positive protection against rust and corrosion. LUBRIPLATE No. 4 is an SAE 90 gear lubricant. LUBRIPLATE No. 4 is recommended extensively for medium to medium slow speed, heavy-duty bearings, enclosed gear cases, gear head motors, heavy way lubricant and wherever an oil of this viscosity is required for industrial applications. Data Sheet